Wuxi Hengnuo Chemical Equipment Manufacturing Co.,Ltd.
Home > News > Content
Application And Maintenance Of Laboratory Reaction Kettle
- Sep 01, 2017 -

Application and maintenance of laboratory Reaction Kettle
     Use of laboratory Reaction Kettle
       The use of laboratory Reaction Kettle must be closed refrigerant inlet valve, put the virus inside the pot and jacket the remaining refrigerant, and then into the Reaction Kettle input material, start the stirrer, and then open the steam valve and electric power, to reach the required temperature, Should be closed before the steam valve and electric power, after 2 to 3 minutes, and then turn off the Reaction Kettle stirrer, after processing, put the pot and jacket after the remaining condensate, should be washed with warm water as soon as possible, brush off the Reaction Kettle Sticky material, and then use 40 ~ 50 0 C alkaline water in the laboratory Reaction Kettle container wall full cleaning, and rinse with water, special pot no material (heat-absorbing medium) empty pot case, not open the steam valve and electric Power, with particular attention to the use of steam pressure, shall not exceed the laboratory Reaction Kettle quota working pressure.
     Maintenance of laboratory Reaction Kettle
      Maintenance of the Reaction Kettle to pay attention to the entire Reaction Kettle equipment and reducer work, reducer lubricants should be added immediately, electric heating medium oil to be replaced every six months, the jacket and the lid on the upper parts of the safety valve, Pressure gauge, thermometer, distillation hole, electric bar, electrical and other equipment should be regularly checked, if there is a fault to immediately exchange or repair the Reaction Kettle, the Reaction Kettle equipment is not necessary, must use warm water in the Reaction Kettle inside and outside the container full cleaning, Scrub the pot body, keep the surface clean and the liner bright, to achieve the purpose of Reaction Kettle durability.
    Laboratory Reaction Kettle are widely used in universities, research and experimental departments. The general understanding of the laboratory Reaction Kettle is a physical or chemical reaction of stainless steel containers, through the container structure design and parameter configuration, to achieve the process requirements of heating, evaporation, cooling and low, high-speed mixing function.
    The pressure requirements of the Reaction Kettle during reaction are not the same for the design of the Reaction Kettle vessel. Laboratory Reaction Kettle production must be in strict accordance with the corresponding standard processing, testing and test Reaction Kettle equipment.
  When using the Reaction Kettle, you must close the refrigerant inlet valve, remove the remaining refrigerant inside and inside the jacket, then enter the material, start the stirrer, and then open the steam valve and electric power, to reach the required temperature, you should turn off the steam Valves and electric power, after 2 to 3 minutes, and then off the mixer, after processing, put the pot and jacket after the remaining condensate, should be washed with warm water as soon as possible, brush off the sticky material, and then use 40 ℃ ~ 50 ℃ Alkaline water in the container wall full cleaning, and rinse with water, special pot no material (heat-absorbing medium) empty pot case, shall not open the steam valve and electric power, with particular attention to the use of steam pressure, not exceeding the fixed working pressure The
    Maintenance of the Reaction Kettle to pay attention to the work of the entire equipment and reducer, reducer lubricants should be immediately added, electric heating medium oil to be replaced every six months, the jacket and the upper part of the lid safety valve, pressure gauge , Distillation holes, electric rods, electrical instruments, etc. should be regularly checked, if there is a fault to immediately exchange or repair, equipment, when not in use, must be warm water in the container inside and outside the wall full cleaning, often scrub the pot body, keep the appearance clean and liner bright , To achieve the purpose of durability.
Although the laboratory Reaction Kettle to open the hole, and after a long period of air replacement and natural cooling, with access conditions, but people close to the hole or feel the heat wave blowing.
Laboratory Reaction Kettle inside the pipeline, almost no man moved to move the space. As the hole and the nearest pipeline distance of only about 40 cm, into the Reaction Kettle is the first hurdle. Chen Yaoming grasp the hole into the hole, lift legs, bow waist, arm, stuck out the hole along the hole to the Reaction Kettle slowly moving. After the pragmatic air distribution board, he bent into the kettle. Subsequently, colleagues Liu Yidong and Cao Jibin also drilled in.